Universal JTAG library, server and tools ======================================== Kolja Waschk (Ed.) $Id $ ///////////////////////////////////////////////////////////////////////////// This document is formatted to be readable for "asciidoc". Before you make any changes, please read the use guide at the asciidoc home page www.methods.co.nz/asciidoc and try to adapt to the style used here; e.g. use the single-line section header style ("== header =="). ///////////////////////////////////////////////////////////////////////////// == Copyright == Copyright 2007, 2008 Kolja Waschk (and the respective authors) Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation. A copy of the license is included in the section entitled "GNU Free Documentation License". //========================================================================= == General == === JTAG === JTAG basics can be found all over the internet. This section should go into some more details about working with JTAG. What hardwarde do you need, what is the usage of JTAG, where do I get files. What file formats are available... ==== Introduction ==== JTAG (IEEE 1149.1) is a serial interface for testing devices with integrated circuits. The problem that the JTAG interface was designed to solve is checking if connections between ICs are OK. Therefore you can set and check in- and outputs of ICs. In order to save pins and logic a very simple serial design was invented. * One pin serial input * One pin serial output * One pin clock * One pin control The control pin (together with clock) allows to switch device states. A state machine inside each chip can be controlled, e.g. to reset the device. This control machine also allows to have two internal shift registers in each device (although we only have on in- and one output-pin). The registers are called instruction register (IR) and data register (DR). The current UrJTAG tool allows you to set the IR and set and get the DR. It doesn't allow you to directly control the statemachine (yet). ==== Interfaces ==== The simplest interface that you can build is the Xilinx parallel cable (also called DLC5). If your device works with a 5V or 3.3V supply voltage then this device can even be build just with passive parts. (picture missing here) UrJTAG also supports a number of other interface adapters. ==== Additions ==== In the meantime the jtag specification was used as a basis for programming flash files and debugging processors. UrJTAG supports programming a couple of different flash devices. It also supports programming of non-flash devices via svf files. UrJTAG does not support debugging yet. Other open source solutions such as OpenOCD allow you to debug ARM processors with gdb. ==== BSDL and UrJTAG data files ==== The bsdl file format describes the jtag interface for one IC. It is a vhdl syntax with the needed information (like pin-names, register lengths and commands) that is usually done by the supplier. e.g. the Xilinx .bsd files are all included in their free web-pack. Urjtag uses a different file format internally. So in order to add a new device to UrJTAG you need to convert those files and produce a directory structure. Currently there are at least three tools available to do that. Please ask on the mailing list in case of problems with that. Please also send proven working files back to this project. ==== SVF files ==== The svf file format contains a number of high level commands to drive the jtag bus. For example you can shift the IR or DR and even check for the results. The Xilinxs impact tool allows you to write this file to program devices. //------------------------------------------------------------------------ === UrJTAG === ==== Introduction ==== UrJTAG Tools is a software package which enables working with JTAG-aware (IEEE 1149.1) hardware devices (parts) and boards through JTAG adapter. This package has open and modular architecture with ability to write miscellaneous extensions (like board testers, flash memory programmers, and so on). JTAG Tools package is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. There is absolutely no warranty for JTAG Tools. Please read COPYING file for more info. WARNING: This software may damage your hardware! Feedback and contributions are welcome. ==== UrJTAG Website ==== The most current version of this documentation and UrJTAG sourcecode is always available from the project page at Sourceforge, http://urjtag.sourceforge.net ==== The name "UrJTAG" ==== I (Kolja) favour short names, so I thought about adding only a few letters to "JTAG". The prefix "Ur" in German means "ancestral", an "Ur-Vater" is a forefather. UrJTAG shall become the forefather, the basis for many other JTAG tools. ==== Authors, contributors, ... thanks ==== A list of contributors is maintained in the file THANKS in the source distribution. ==== UrJTAG and openwince JTAG Tools ==== The JTAG Tools originally were developed by Marcel Telka as part of the openwince project. Still a large portion of the source code is his work. However, the last release of the JTAG tools was version 0.5.1 in 2003. After a few years the development completely stalled. Every few months or so on the project's mailing list someone asked about continuing, but a critical mass wasn't reached before late 2007. A fork of the JTAG tools was created under the wings of the UrJTAG project at Sourceforge. //------------------------------------------------------------------------ === System requirements ==== //Copied from original README ==== Supported host operating systems ==== JTAG Tools should run on all Unix like operating systems including MS Windows with Cygwin installed. ==== Required software for running UrJTAG ==== Required only for MS Windows: * current Cygwin net installation from http://cygwin.com * ioperm package (a part of the standard Cygwin net installation) It may be necessary to run the command "ioperm -i" to install the IOPERM.SYS driver in the system. Required for all systems: * readline (it is probably a standard part of your distribution) More software is needed if you want to compile UrJTAG (which you probably want because currently no pre-compiled binaries are avaible...). See "Installation" below. ==== Supported JTAG adapters/cables ==== See 'help cable' command for up-to-date info. * Arcom JTAG Cable * Altera ByteBlaster/ByteBlaster II/ByteBlasterMV Parallel Port Download Cable * Xilinx DLC5 JTAG Parallel Cable III * ETC EA253 JTAG Cable * ETC EI012 JTAG Cable * Keith & Koep JTAG Cable * Lattice Parallel Port JTAG Cable * Mpcbdm JTAG Cable * Ka-Ro TRITON (PXA255/250) JTAG Cable * Macraigor Wiggler JTAG Cable ==== JTAG-aware parts (chips) ==== The data/ directory of the UrJTAG installation has some more, but at least the following are supported: * Altera EP1C20F400 * Altera EPM7128AETC100 * Analog Devices Sharc-21065L * Atmel ATmega128 (partial support) * Broadcom BCM1250 * Broadcom BCM3310 (partial support) * Broadcom BCM5421S * Broadcom BCM4712 (partial support) * DEC SA1100 * Hitachi HD64465 * Hitachi SH7727 * Hitachi SH7729 * IBM PowerPC 440GX * Intel IXP425 * Intel SA1110 * Intel PXA250/PXA255/PXA260/PXA261/PXA262/PXA263 * Lattice LC4032V * Lattice M4A3-64/32 * Lattice M4A3-256/192 * Motorola MPC8245 * Samsung S3C4510B * Sharp LH7A400 * Toshiba TX4925/TX4926 * Xilinx XC2C256-TQ144 * Xilinx XCR3032XL-VQ44 * Xilinx XCR3128XL-CS144 * Xilinx XCR3128XL-VQ100 * Xilinx XCR3256XL-FT256 ==== Flash chips ==== NOTE: Not all chips are supported in every possible configuration, there may be untested combinations of chip type, bus width, ... * Intel 28FxxxJ3A (28F320J3A, 28F640J3A, 28F128J3A) * Intel 28FxxxK3 (28F640K3, 28F128K3, 28F256K3) * Intel 28FxxxK18 (28F640K18, 28F128K18, 28F256K18) * AMD Am29LV64xD (Am29LV640D, Am29LV641D, Am29LV642D) * AMD Am29xx040B (Am29F040B, Am29LV040B) //------------------------------------------------------------------------ === Installation === ==== Required software for compiling UrJTAG ==== To run autogen.sh, you need autoconf and automake, bison, and a recent flex. Flex 2.5.4a as it comes with Cygwin will work but some parts of UrJTAG (namely the SVF player) become more verbose if Flex 2.5.31 or newer is used. Furthermore, libtool should be available, and "devel" versions of the following packages: * gettext * readline If you plan to use any USB adapter with Linux, libusb-dev and probably libftdi-dev are a good choice (that are Debian package names; other distributions certainly have similar packages). On Windows, the FTDI FTD2XX library should work: * http://libusb.sourceforge.net (libusb) * http://libusb-win32.sourceforge.net (libusb for Windows) * http://www.intra2net.com/de/produkte/opensource/ftdi/ (libftdi) * http://www.ftdichip.com/Drivers/D2XX.htm (FTDI FTD2XX library) ==== Installing from source tar.gz ==== The installation follows the standard configure, make, make install scheme: tar xzvf urjtag.tar.gz cd ../jtag ./configure make make install ==== Installing from Suvbersion repository ==== If you want to try the very newest version of UrJTAG... svn co http://urjtag.svn.sourceforge.net/svnroot/urjtag/trunk urjtag cd urjtag/jtag ./autogen.sh # ./configure is run by autogen.sh make make install //========================================================================= == Usage == === Quick start === //Contributed by Ralf Engels ==== Run the software ==== Connect your JTAG adapter between your PC and target device and turn on your device. To run JTAG Tools type "jtag" and press Enter. jtag should start and display some initial informations. Output should end with line like this: This is "jtag command prompt". Type "help" and press Enter for initial help about available commands. To exit JTAG Tools type "quit" and press Enter. ==== Configure the cable ==== Type "help cable" for list of supported JTAG cables. Type "cable" command with arguments. Example: jtag> cable EA253 parallel 0x378 Initializing ETC EA253 JTAG Cable on parallel port at 0x378 ==== Detect parts on the JTAG chain ==== Type "detect" at the jtag command prompt: jtag> detect Your output should look like this: IR length: 5 Chain length: 1 Device Id: 01011001001001100100000000010011 Manufacturer: Intel Part: PXA250 Stepping: C0 Filename: /usr/local/share/jtag/intel/pxa250/pxa250c0 If you get empty output or an error message your JTAG adapter is not connected properly, or your target board doesn't work, or it is turned off. The "detect" command is required before all other commands. ==== Print current JTAG chain status ==== jtag> print chain No. Manufacturer Part Stepping Instruction Register --------------------------------------------------------- 0 Intel PXA250 C0 BYPASS BR ==== Sample device pin status ==== jtag> instruction SAMPLE/PRELOAD jtag> shift ir jtag> shift dr jtag> dr 1000110010000010000110010111111111111111111001101110... jtag> print chain No. Manufacturer Part Stepping Instruction Register ------------------------------------------------------------ 0 Intel PXA250 C0 SAMPLE/PRELOAD BSR jtag> get signal BOOT_SEL[0] BOOT_SEL[0] = 0 jtag> Note: BSR is "Boundary Scan Register" ==== Burn flash connected to the part ==== jtag> flashmem 0 brux.b 0x00000000 Note: Supported configuration is 2 x 16 bit only BOOT_SEL: Asynchronous 32-bit ROM 2 x 16 bit CFI devices detected (QRY ok)! program: block 0 unlocked erasing block 0: 0 addr: 0x00002854 verify: addr: 0x00002854 Done. jtag> or: jtag> flashmem msbin xboot.bin Note: Supported configuration is 2 x 16 bit only BOOT_SEL: Asynchronous 32-bit ROM 2 x 16 bit CFI devices detected (QRY ok)! block 0 unlocked erasing block 0: 0 program: record: start = 0x00000000, len = 0x00000004, checksum = 0x000001EB record: start = 0x00000040, len = 0x00000008, checksum = 0x000001B0 record: start = 0x00001000, len = 0x00002B30, checksum = 0x00122CAB record: start = 0x00004000, len = 0x00000160, checksum = 0x0000684B record: start = 0x00005000, len = 0x00000054, checksum = 0x000008EE record: start = 0x00005054, len = 0x00000030, checksum = 0x00000DA9 record: start = 0x00000000, len = 0x00001000, checksum = 0x00000000 verify: record: start = 0x00000000, len = 0x00000004, checksum = 0x000001EB record: start = 0x00000040, len = 0x00000008, checksum = 0x000001B0 record: start = 0x00001000, len = 0x00002B30, checksum = 0x00122CAB record: start = 0x00004000, len = 0x00000160, checksum = 0x0000684B record: start = 0x00005000, len = 0x00000054, checksum = 0x000008EE record: start = 0x00005054, len = 0x00000030, checksum = 0x00000DA9 record: start = 0x00000000, len = 0x00001000, checksum = 0x00000000 Done. jtag> //------------------------------------------------------------------------ === JTAG commands === ==== Overview ==== Following is a list of commands currently supported by jtag and some example usage. *bit*:: define new BSR bit *bus*:: change active bus *cable*:: select JTAG cable *detect*:: detect parts on the JTAG chain *detectflash*:: detect parameters of flash chips attached to a part *discovery*:: discovery of unknown parts in the JTAG chain *dr*:: display active data register for a part *endian*:: set/print endianess *eraseflash*:: erase flash memory by number of blocks *flashmem*:: burn flash memory with data from a file *frequency*:: setup JTAG frequency *get*:: get external signal value *help*:: display this help *include*:: include command sequence from external repository *initbus*:: initialize bus driver for active part *instruction*:: change active instruction for a part or declare new instruction *part*:: change active part for current JTAG chain *peek*:: read a single word *poke*:: write a single word *print*:: display JTAG chain list/status *quit*:: exit and terminate this session *readmem*:: read content of the memory and write it to file *register*:: define new data register for a part *script*:: run command sequence from external file *set*:: set external signal value *setdevice*::: force device detection *shift*:: shift data/instruction registers through JTAG chain *signal*:: define new signal for a part *svf*:: execute svf commands from file ==== Basic commands ==== ===== quit ===== This command closes the jtag console. ===== help ==== Without additional parameter it gives an overview of the available commands. With a parameter you can get more information about any of the commands. Example: jtag> help cable ==== Part definition commands ==== The following commands are also used in the data files to define a device (IC) on the jtag bus. It is not recommended to use these commands in an interactive session. Instead you should produce a device definition file out of a .bsd file using one of the supplied tools. * bit * register * signal ==== Flash commands ==== These commands can be used if the device supports flashing. * detectflash * flashmem * eraseflash ==== Chain management ==== ===== cable ===== Sets and initialized the cable driver. This is usually the first command that you are executing in a session. Example: jtag> cable EA253 parallel 0x378 Initializing ETC EA253 JTAG Cable on parallel port at 0x378 For a parallel cable using the ppdev driver you would use this: jtag> cable DLC5 ppdev /dev/parport0 If you get an error, it may be that the parallel port kernel driver was compiled as a module in your Linux kernel and wasn't loaded automatically. Then you should try to load the ppdev driver manually (with root rights outside the jtag shell): modprobe ppdev modprobe parport modprobe parport_pc ===== detect ===== Detects devices on the bus. Example: jtag> detect IR length: 5 Chain length: 1 Device Id: 01011001001001100100000000010011 Manufacturer: Intel Part: PXA250 Stepping: C0 Filename: /usr/local/share/jtag/intel/pxa250/pxa250c0 ===== setdevice ===== //From README_21065L This command is currently only there to support the SHARC 21065L processor, which has no IDCODE. In jtag prompt type command "setdevice sharc21065L", now the mode changes to SHARC 21065L specific. Note that this mode works only with SHARC 21065L processor. If you want to try another device, please restart the JTAG tool. jtag> setdevice sharc21065L Device is set to SHARC 21065L //======================================================================== == Internals == This section yet is only a placeholder for the information that will be added soon... === Files === ==== Source code Overview ==== data/ include/ inclow/ libbrux/ cmd/ flash/ src/ bus/ cmd/ lib/ tap/ svf/ ==== Data file format ==== //By Marcel Telka JTAG declarations files are located in directory data. The files contains common part specific JTAG information in parseable form, e.g. list of the JTAG commands, boundary scan register, list of JTAG registers, etc. Syntax of the JTAG declaration file is defined in the following subsections. ===== General rules ===== JTAG declaration file is text file which consists of lines. Empty lines are ignored. Text after first # on the line to the end of line is ignored. This is useful for comments. All other lines are significant. Each significant line consists of tokens separated by whitespace. Whitespace could be spaces and/or tabs. ===== Signal Definition ===== Signal definition line consists of word signal followed by whitespace and signal name (without spaces in the name). Rest of the line should contain whitespace separated list of pins of the part. This list is currently not used for any purpose in JTAG Tools. It is intended for future use. //------------------------------------------------------------------------ === Drivers === * Parport drivers * Cable drivers * TAP drivers * Chain drivers * Bus drivers * Flash drivers * Commands //------------------------------------------------------------------------ === Development === ==== Future Plans ==== - C API and library package - Bindings for Python, Perl, ... - TCP/IP access - New cable drivers - ... ==== How to contribute ==== * Using Subversion * Create and submit a patch * Use SourceForge trackers //======================================================================== == F.A.Q. == Q. When I type "cable parallel 0x378 DLC5" on Windows XP I get "Error: Cable initialization failed!". Where is the problem?:: A. Please install ioperm.sys driver using `ioperm -i` command. Q. When running autogen.sh, I get "Can't exec "autopoint": No such file or directory":: A. You need the headers for gettext (e.g. Debian package "gettext-devel"). Q. During compilation, I get "svf_bison.y: No such file or directory":: A. You need "bison". Q. During compilation, I get "flex: can't open ... src/svf/svf_flex.l":: A. You need "flex" Q. During compilation, I get "src/svf/svf_flex.l", line 27: unrecognized %option: bison-locations":: A. You need a newer version of flex. It should be 2.5.31 or newer; Unfortunately, Cygwin comes with only 2.5.4a. You may try to compile and install a newer version of flex from source to solve this. //========================================================================