$Id$ SVF Player for JTAG Tools ~~~~~~~~~~~~~~~~~~~~~~~~~ This README describes the SVF player of the JTAG Tools software package. The player has been developed according to the "Serial Vector Format Specification", Revision E, 8 March 1999 issued by ASSET InterTech, Inc. The full specification can be found at http://www.asset-intertech.com/support/svf.pdf Copyright --------- SVF player is copyright 2004, Arnim Laeuger. Parser and lexer are also copyright 2002, CDS at http://www-csd.ijs.si They have been reused from the "Experimental Boundary Scan" project at http://ebsp.sourceforge.net/ The SVF player is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. There is absolutely no warranty for this software. Please read the file COPYING for more info. Usage ----- The SVF player operates on a single part in the scan chain. Therefore, you have to bring up the JTAG Tools software, specify a cable and detect the scan chain beforehand. The player will establish a new instruction called "SIR" and a new register called "SDR". They are used internally by the respective SVF commands and are reassigned with new values as the player advances through the file. It is not recommended to use them outside of the SVF player as their content is dynamic. Example session: jtag> cable ppdev /dev/parport0 DLC5 Initializing Xilinx DLC5 JTAG Parallel Cable III on ppdev port /dev/parport0 jtag> detect IR length: 5 Chain length: 1 Device Id: 10010000101000100000000010010011 Manufacturer: Xilinx Part: XC2S300E-PQ208 Stepping: 9 Filename: /usr/local/share/jtag/xilinx/xc2s300e-pq208/xc2s300e-pq208 jtag> part jtag> svf jtag> instruction BYPASS jtag> part jtag> svf jtag> instruction BYPASS ... It is recommended to set the part's instruction register to BYPASS although most SVF files do this at the end. By setting the instruction explicitely to BYPASS the output of the print command will always show meaningful information. The SVF player will issue messages when situations arise that cannot be handled. These messages are classified as warnings or errors depending on whether the player can continue operation (warning) or not (error). In case the TDO parameter of an SDR command leads to a mismatch the player issues a warning and continues. If the player should abort in this case then specify 'stop' at the svf command. Limitations and Deficiencies ---------------------------- Several limitations exist for the SVF player. It has been tested with files generated by these tools so far: + Xilinx ISE WebPack 6.3.02i - 9.1.02i + Altera Quartus II 4.1sp1 - 7.0 Configuration for these devices has been tested so far: + Altera EPC1C12Q240 + Altera MAX3032, EPM3032ALC44 + Altera MAX3064, EPM3064ALC44 + Altera MAX7032, EPM7032SLC44 + Altera MAX7064, EPM7064SLC44, EPM7064STC44 + Xilinx Spartan-IIE, XC2S300E-PQ208 + Xilinx Spartan-3, XC3S1000-FG456, XC3S5000-FG900 The implementation of some SVF commands has deficiencies. - HIR, HDR Commands not supported. Their functionality should be covered by the part concept of JTAG Tools. - PIO Command not supported. - PIOMAP Command not supported. - RUNTEST SCK not supported. The maximum time constraint is not guaranteed. - SIR No check is done against the TDO parameter. - TRST Parameters Z and ABSENT are not supported. - TIR, TDR Commands not supported. Their functionality should be covered by the part concept of JTAG Tools. Warning and error messages don't mention the line in the SVF file where the issue was detected. Operation is slowed down significantly when the FREQUENCY command has been specified. This is not a problem of the SVF player itself but seem to happen when the frequency of JTAG Tools is set to a value larger than 0. Configuration takes very long although the maximum allowed frequency is 10 MHz. Consider to comment out the FREQUENCY command at the beginning of the SVF file. Contact ------- Sharing your experience with this software is highly welcome. Please direct issues either to the openwince-list mailinglist at http://lists.sourceforge.net/mailman/listinfo/openwince-list or contact me directly arniml users.sourceforge.net